|
The only slip resistant finish that is safe to use on
marble & terrazzo. Non-acid, breathable. High traffic. Will not harm tile surface. Use on all
types of interior resilient and hard floors including: marble, terrazzo, natural stone, ceramic
tile, wood, rubber, VCT, lino and old vinyl asbestos tile.
* Gaseous membrane allows surface to breathe, which is important with hard
floors such as marble, etc.
For interior resilient and hard floors. Durable, scuff, scratch, black heel
mark, and UV resistant. Simple, safe, tough, highest quality, low end-use cost. The ultimate
in floor care finish for durability.
- The ultimate in high glass transitional temperature
- Greater gloss restoration capabilities'
- Repels impregnation of foreign particles and black heel marks.
- Recoat time 1/3 of industry standard
- Clarity and leveling ability allows for traffic lane touch up and blending,
no need to re-coat entire floor
- Easy to remove if necessary (with Flexstrip)
- Use Flexclean to clean and restore gloss and Flexclean AB to disinfect
- Use On Guard to degrease
Dries and cures from the bottom up in 15 minutes.
Rapid coating is possible. Can be walked on wet without permanently harming the integrity
of the floor finish. Burnish to speed-up the curing process and improve durability. Savings
of as much as 20% in chemical costs over a three year period, when used as directed. Use
Flexseal to restore old or brittle resilient floors.
Because the Finish dries and cures from the bottom up,
porosity and poor film integrity caused by the coalescent 'out-gassing' of top down drying is
eliminated. Flexfinish is safer for the environment. Mitigates potential regulatory problems
for end-users. Metal-free waste discarded down the drain after stripping will not interfere
with the sewage treatment process. Coverage is approx. 3000 sq. ft. / gal. (2 times industry
standard), based upon one coat. Five coats recommended.
Doesn't powder or shear off when burnished. Resists pad
burns and soil embedment from ultra high-speed equipment. Does not add polymer dust to building
environment.
User-friendly, with virtually no mop drag. Use H.T.
Rayon Mop to apply. Levels easily; blends into traffic lanes without color change. Burnish
blend wet edge when possible. Can be coated over a stable conventional finish or sealer.
Solvent and mild acid resistant. Resists alcohol,
oils, medications and most food spills.
More uniform gloss. Better adhesion of floor finish.
A slight mop drag can indicate the floor is improperly neutralized. Capable of transforming
small amount of residual alkali after stripping, and when floor is improperly neutralized,
into floor finish while allowing the remaining alkali to escape from the film.
Solids: 25 plus %
pH: 8.8 + / - 0.1
Color: Milky White
Dry Film Character: Clear, Water White
Oven test 52: Stable
Stability: 30 Days
|
Slip Resistance (up to): .55 to .8 ASTM 2047-82
Leveling: 9/10*
Gloss levels at 60°
(4 coats on black vinyl composition):
92
Water Spot Resistance
(4 coats, 1 hour cure time on pure vinyl tile):
9/10*
Drying Time: 10/15 minutes
Re-coatability: 15 minutes
Detergent Resistance: 8/9*
Black Mark Resistance: 10*
Powdering Resistance: 10*
Buffability: 10*
Sward Rocker Hardness: 80/90
100% Modulus: 5000/6600 P.S.I.
Tensile Strength: 4800/7000 P.S.I.
Elongation At Break: 425%
Application Temperature:
35°F min. to 90°F max.
* Code: 1=Poor 10=Excellent
Force drying, due to internal thermal accelerator.
Equipment cleanup use water. High gloss / burnishable with HT blue pad. No solvent
coalescent; no offensive odour in product. Non-discoloring, contains no styrene
- If floor has been stripped, ensure floor has been neutralised and clear
water rinsed properly prior to finish application procedures. If floor has
been scrubbed using 'Flexclean', neutralising is not essential, however, a
clear water rinse is required. Check pH of floor to ensure it is not below pH 7 (acidic).
- Assemble all equipment, chemicals and custodial hardware prior to beginning
procedures. Read safety instructions on MSDS and chemical product labels and comply
as directed.
- Pour Flexfinish in a wringer bucket lined with a plastic bag. Immerse clean,
prebroken in, lint free, dedicated H.T. Rayon Floor Finish Mop fully in finish.
Wring out bottom half of mop. (New mops should be soaked in clean water first,
to remove loose fibres and residue.)
- Apply 5 or 6 medium coats depending upon porosity of floor, desired appearance,
traffic conditions, etc.
- For best results, apply one full coat and burnish very well with H.T. Blue
Pad to anchor Flexfinish to tile until a gloss appears. Then apply another 4
coats and burnish final coat. Use a 1000 to 2500 R.P.M. burnisher. If using as a
Dry Brite finish, burnishing is not required. If using a scrub and re-coat procedure,
after applying 3 coats of Flexfinish H.T., burnish the final coat. Dust mopping after
burnishing is not required.
- Flexfinish H.T. blends in perfectly with previous coats if recommended maintenance
procedures have been performed. If this is a re-coat after scrubbing (not stripping),
or in an area where the coating is to be blended in, apply coats directly on the
affected area(s).
OPTIONAL: You may wish to burnish the entire floor
prior to the application to locate the 'hot spots' that need re-coating. For maximum
durability, re-coat (2 to 3 coats) in the areas that do not 'pop' a shine after burnishing.
Burnish blend the wet edges around each patch you re-coat. In the case of an alkaline spill,
after three coats, burnish entire area affected. If not satisfied, re-coat until shine matches
remainder of floor.
NOTE: 'Flexseal' is highly recommended for all resilient floors as it
will greatly enhance the floor finish and increases its durability.
Flexfinish is slip resistant on dry surfaces. To impart slip resistance on wet surfaces, we recommend Maxiflex HT. This product cannot totally eliminate the possibility of slipping.
|
